X2CrNiN18-10 | 1.4311 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full Access Best valueMaterial Description
| Material Number | Material Name | Material Number (single) | Standard | Scope | Standard Status | Country | Successor | VDA 231-106 classification | |
|---|---|---|---|---|---|---|---|---|---|
| 1.4311 (DIN 17458 : 1985-07) | X2CrNiN18-10 | 1.4311 | DIN 17458 : 1985-07 | DIN 17458 : 1985-07 replaced by DIN EN 10216-5 : 2004-11 | Replaced | Germany | X2CrNiN18-10 | 1.1.2 | 1) |
| 1) Remark: The austenitic CrNi-steel X2CrNiN18-10, comparable to X 2 CrNiN 18 10 acc. to DIN 17440 : 1985-07 (invalid), shows a higher yield point by nitrogen alloying which survives also at higher temperatures. This is used in pressure vessel and leightweight construction. Improvement of the corrosion resistance by its N-content. The material is resistant to intercrystalline corrosion also in sensitized condition. Suitability for chemical apparatus engineering owing to resistance to nitric acid and other oxidizing media. This steel is well cold formable and suitable for mirror finishing. Excellent applicability for refrigeration up to -270 deg. due to its cryogenic toughness (for the comparable DIN-mark). |
Chemical Composition
| C [%] | Cr [%] | Mn [%] | N [%] | Ni [%] | P [%] | S [%] | Si [%] | Remainder | |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| 1) Source: blur |
Material Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
Mechanical Properties
| Semi-finished Product | Condition | Nominal Size [mm] | Temperature [°C] | Specimen Direction | Tensile Strength [MPa] | Yield Strength (0.2% offset) [MPa] | Yield Strength (1.0% offset) [MPa] | Elongation A [%] | |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| blur | blur | blur | blur | blur | 1)3) | ||||
| 1) Source: blur | |||||||||
| 2) Remark: blur | |||||||||
| 3) Remark: blur |
Toughness Data (Impact)
| Semi-finished Product | Condition | Nominal Size [mm] | Temperature [°C] | Specimen Shape | Specimen Direction | Notch Impact Energy [J] | |
|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | |||||||
| 2) Remark: blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur |
Linear-elastic
| Temperature [°C] | Young's modulus [GPa] | Bulk modulus [GPa] | Shear modulus [GPa] | Poisson's ratio |
|---|---|---|---|---|
| blur | blur | |||
| blur | blur | |||
| blur | blur | |||
| blur | blur | |||
| blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Alternating stress
| Temperature [°C] | Stress ratio | Mean stress [MPa] | Alternating stress [MPa] | Cycles |
|---|---|---|---|---|
| blur | blur | blur | blur | |
| blur | blur | blur | blur | |
| blur | blur | blur | blur | |
| blur | blur | blur | blur |
Designation
| Designation | Material number | Source |
|---|---|---|
| blur | blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur | ||
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |