EN-GJMB-550-4 | 5.4207 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full Access Best valueMaterial Description
| Material Number | Material Name | Material Number (single) | Standard | Scope | Standard Status | Country | Predecessor | Successor | VDA 231-106 classification | |
|---|---|---|---|---|---|---|---|---|---|---|
| 5.4207 (DIN EN 1562 : 2012-05) | EN-GJMB-550-4 | 5.4207 | DIN EN 1562 : 2012-05 | DIN EN 1562 : 2012-05 replaced by DIN EN 1562 : 2019-06 | Replaced | Germany | EN-GJMB-550-4 | EN-GJMB-550-4 | 1.2 | 1) |
| 1) Remark: Material EN-GJMB-550-4 (former GTS-55-04 acc. to DIN 1692-82) is an all-black malleable cast iron which is used for crankshafts, camshafts, rocking levers, shift-forks, spring brackets, swivel heads, joint flanges, wheel hubs, rear-axle casings, water barriers, pivot bearings as well as for pinion cages for automatic transmissions. Malleable iron can be used for pressure equipment, e.g. fittings (with thread, with clamp joint) for compressed-air, water (hot and cold), oil, steam, gas as well as for industry fittings (housings, covers, upper parts) and diaphragm valves. The appropriate materials for pressure applications and the conditions of use are specified in special product standards or application standards. For the structuring of pressure equipment special construction guidelines applies. |
Chemical Composition
| C [%] | Mn [%] | S [%] | Si [%] | Remainder | |
|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | |||||
| 2) Remark: blur |
Material Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
Mechanical Properties
| Semi-finished Product | Condition | Nominal Size [mm] | Temperature [°C] | Tensile Strength [MPa] | Yield Strength (0.2% offset) [MPa] | Elongation A3,4 [%] | Hardness HB | HBW | |
|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| 1) Source: blur |
Physical Properties
| Temperature [°C] | Density [g/cm³] | Young's Modulus [GPa] | Thermal Conductivity [W/(m*K)] | Specific Electrical Resistance [µΩm] | Mean Specific Heat Capacity [kJ/(kg*K)] | |
|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | ||||||
| 2) Remark: blur |
Toughness Data (Impact)
| Semi-finished Product | Condition | Temperature [°C] | Specimen Shape | Notch Impact Energy [J] | |
|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | |||||
| 2) Remark: blur |
FKM Guideline Fatigue Strength
| Semi-finished Product | Condition | Nominal Size [mm] | Tensile Strength [MPa] | Yield Strength (0.2% offset) [MPa] | Elongation A3 [%] | Fatigue Limit under rev. Tension-Compression Stresses [MPa] | Fatigue Strength under pulsating Tensile Stresses [MPa] | Bending Fatigue Strength [MPa] | Shear Fatigue Strength [MPa] | Torsion Fatigue Strength [MPa] | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | |||||||||||
| 2) Remark: blur |
Cross Reference
| Material Name | Country | Standard | |
|---|---|---|---|
| JMB/550-4 | Australia | AS 1832 | 1) |
| KTZ550-04 | China | GB/T 9440 | 2) |
| C02551 | China | GB/T 9440 | 1) |
| EN-GJMB-550-4 | Europe | EN 1562 | |
| PM550 | India | IS 14329 | 2) |
| JMB/550-4 | International | ISO 5922 | 2) |
| FCMP55-04 | Japan | JIS G 5705 | 2) |
| KC55-4 | Russia | GOST 1215 | 2) |
| KČ55-4 | Russia | GOST 1215 | 2) |
| KЧ55-4 | Russia | ГОСТ 1215 | 2) |
| A220 Grade 60004 | USA | ASTM A220 | 2) |
| 60004 | USA | ASTM A220 | 2) |
| Grade 60004 | USA | ASTM A220 | 2) |
| A220M Grade 410M4 | USA | ASTM A220M | 2) |
| 410M4 | USA | ASTM A220M | 2) |
| Grade 410M4 | USA | ASTM A220M | 2) |
| A602 Grade 5003 | USA | ASTM A602 | 2) |
| 5003 | USA | ASTM A602 | 2) |
| Grade 5003 | USA | ASTM A602 | 2) |
| F24130 | USA | UNS | 1) |
| F20002 | USA | UNS | 1) |
| GTS-55-04 | Germany | DIN 1692 | |
| 0.8155 | Germany | DIN 1692 | |
| GJMB550-4 | |||
| EN-JM1160 | |||
| JM1160 | |||
| 1) Source: Stahlschlüssel 2016, Verlag Stahlschlüssel Wegst GmbH, Marbach | |||
| 2) Source: Tirler, W.: Gusseisen, Internationale Werkstoffbezeichnungen und Normen. Beuth Pocket, DIN, Deutsches Institut für Normung e.V., 1. Aufl., Berlin, 2015, Beuth Verlag |
Producer/Supplier/Trade names
| Tradename | Supplier |
|---|---|
| EN-GJMB-550-4 | VS Guss AG, Solingen |
| EN-GJMB-550-4 | Südguss GmbH, Neu-Ulm |
| EN-GJNB-550-4 | Schönheider Guss GmbH, Schönheide |