Compare Plastics, Metals, and More for Construction, Design, and Simulation - Materials Portal Logo MATERIALS PORTAL

EN-GJLA-XNiCuCr15-6-2 | 5.1500 Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access Best value

Material Description

Material Number Material Name Material Number (single) Standard Scope Standard Status Country Predecessor VDA 231-106 classification
5.1500 (DIN EN 13835 : 2012-04) EN-GJLA-XNiCuCr15-6-2 5.1500 DIN EN 13835 : 2012-04 Supersedes DIN EN 13835 : 2006-08 Valid Germany EN-GJLA-XNiCuCr15-6-2 1.2 1)
1) Remark: EN-GJLA-XNiCuCr15-6-2 has a high resistance to corrosion, especially to alkalis, diluted acids, seawater and saline solutions. It shows enhanced heat resistance, favorable sliding qualities as well as a high thermal expansion coefficient. This austenitic cast iron material (graphite form: lamellar) is nonmagnetizable at low Cr-content. The material (international trading name: Ni-Resist 1) is comparable to UNS F 41000 (USA). Application: pumps, valves, furnace construction parts, liner, piston rings, for unmagnetizable cast parts. I can be used for pressure equipment, e.g. compressor housings. The appropriate materials for pressure applications and the conditions of use are specified in special product standards or application standards. For the structuring of pressure equipment special construction guidelines applies.

Chemical Composition

C [%] Cr [%] Cu [%] Mn [%] Ni [%] P [%] Si [%] Remainder
blur blur blur blur blur blur blur blur 1)
1) Source: blur

Material Compliance

REACh RoHS
blur blur

Mechanical Properties

Semi-finished Product Condition Nominal Size [mm] Temperature [°C] Tensile Strength [MPa] Elongation A [%] Compressive Strength [MPa] Hardness HB | HBW
blur blur blur blur blur blur blur 1)
blur blur blur blur 2)3)
blur blur blur blur 2)3)
blur blur blur blur 2)3)
blur blur blur blur 2)3)
1) Source: blur
2) Source: blur
3) Remark: blur

Physical Properties

Semi-finished Product Temperature [°C] Density [g/cm³] Young's Modulus [GPa] Shear Modulus [GPa] Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] Thermal Conductivity [W/(m*K)] Specific Electrical Resistance [µΩm] Mean Specific Heat Capacity [kJ/(kg*K)]
blur blur blur blur blur blur blur blur 1)2)
blur blur 1)3)
1) Source: blur
2) Remark: blur
3) Remark: blur

Heat Treatment

Heat Treatment Temperature [°C] Holding Time [h] Medium
blur blur blur blur 1)2)
blur blur blur blur 1)3)
1) Source: blur
2) Remark: blur
3) Remark: blur

Cross Reference

Material Name Country Standard
L-NiCuCr 15 6 2 Australia AS 1833 1)
HTANi15Cu6Cr2 China GB/T 26648 2)
EN-GJLA-XNiCuCr15-6-2 Europe EN 13835
AFGNi15Cu6Cr2 India IS 2749 2)
JLA/XNi15Cu6Cr2 International ISO 2892 2)
FCA-NiCuCr15 6 2 Japan JIS G 5510 2)
F41000 USA UNS 2)
A436 Type 1 USA ASTM A436 2)
Type 1 USA ASTM A436 2)
GGL-NiCuCr 15 6 2 Germany DIN 1694
0.6655 Germany DIN 1694
EN-JL3011 Europe
EN-GJLA-XNiCuCr15-6-2 Germany AD 2000 W 3/3
1) Source: Stahlschlüssel 2016, Verlag Stahlschlüssel Wegst GmbH, Marbach
2) Source: Tirler, W.: Gusseisen, Internationale Werkstoffbezeichnungen und Normen. Beuth Pocket, DIN, Deutsches Institut für Normung e.V., 1. Aufl., Berlin, 2015, Beuth Verlag

Producer/Supplier/Trade names

Tradename Supplier
EN-GJLA-XNiCuCr15-6-2 SCHMOLZ + BICKENBACH GUSS GmbH, Krefeld
EN-GJLA-XNiCuCr15-6-2 Procast Guss GmbH, Gütersloh
GGL-NiCuCr 15 6 2 Procast Guss GmbH, Gütersloh
LNi 1 SCHMOLZ + BICKENBACH GUSS GmbH, Krefeld

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur

Density

Temperature [°C] Density [g/cm³]
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Compressive strength

Temperature [°C] Compressive ultimate strength [MPa]
blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur
blur blur blur blur
blur blur blur blur

Coefficient thermal expansion

Related Temperature [°C] Temperature [°C] Coefficient thermal expansion [10^-6*K^-1]
blur blur blur

Specific heat

Temperature [°C] Specific heat [kJ/(kg*K)]
blur blur

Thermal conductivity

Temperature [°C] Thermal conductivity [W/(m*K)]
blur blur

Electrical resistivity

Temperature [°C] Specific electrical resistance [µΩm]
blur blur

Designation

Designation Material number Source
blur blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur
blur blur
blur blur
blur blur
blur blur
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Compressive strength

Temperature [°C] Compressive ultimate strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur

Density

Temperature [°C] Density [g/cm³]
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur
blur blur

Specific heat

Temperature [°C] Specific heat [kJ/(kg*K)]
blur blur

Thermal conductivity

Temperature [°C] Thermal conductivity [W/(m*K)]
blur blur

Electrical resistivity

Temperature [°C] Specific electrical resistance [µΩm]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Similar Materials

Diagram Settings
Diagram Preview
Select properties and click "Preview Diagram"