Compare Plastics, Metals, and More for Construction, Design, and Simulation - Materials Portal Logo MATERIALS PORTAL

EN AW-EAl MgSi(B) | EN AW-6101B Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access Best value

Material Description

Material Number Material Name Material Number (single) Standard Scope Standard Status Country Predecessor Successor VDA 231-106 classification
EN AW-6101B (DIN EN 573-3 : 2003-10) EN AW-EAl MgSi(B) EN AW-6101B DIN EN 573-3 : 2003-10 DIN EN 573-3 : 2003-10 replaced by DIN EN 573-3 : 2007-11 Replaced Germany E-AlMgSi0,5 EN AW-Al MgSi 2.1 1)
1) Remark: Material EN AW-EAl MgSi(B) is produced in a high amount for extruded components. It is food-safe. To the comparable mark E-AlMgSi0,5, mat. No. 3.3207, acc. to DIN 1725-1 : 1983-02 applies: E-AlMgSi0,5 is declarated by the German Electical Engineering Commission (Deutsche Elektrotechnische Kommission) as alloy for electrical engineering with a warranted electrical conductivity acc. to DIN 40 501 part 1 to part 4. This cold and warm hardenable material achieves strength values from 200 to 250 MPa at A5-ductile yield of approx. 10 %. Heat-treatment for hardening: solution annealing: 525 to 540 °C quenching in air or water natural aging: 5 to 8 d at RT artificial aging: 4 to 16 h at 155 to 190°C. In warm or cold hardened condition the alloy is only limited formable in soft material condition it is well formable. Weldability, corrosion resistance and anodizability are well. The alloy E-AlMgSi0,5 is predominantly used for busbars and for flat-, section- or tube-busbars. Application: electrical engineering (busbars)

Chemical Composition

Cu [%] Fe [%] Mg [%] Mn [%] Si [%] Zn [%] Remainder
blur blur blur blur blur blur blur 1)2)
1) Source: blur
2) Remark: blur

Material Compliance

REACh RoHS
blur blur

Mechanical Properties

Semi-finished Product Condition Designation of the delivered Condition DIN Delivery Condition EN Nominal Size [mm] Temperature [°C] Specimen Direction Tensile Strength [MPa] Yield Strength (0.2% offset) [MPa] Elongation A [%] Elongation A50 [%]
blur blur blur blur blur blur blur blur blur blur blur 1)2)
blur blur blur blur blur blur blur blur blur blur blur 1)2)
blur blur blur blur blur blur blur blur blur blur blur 1)3)
blur blur blur blur blur blur blur blur blur blur blur 1)3)
blur blur blur blur blur blur blur blur blur blur blur 1)3)
1) Source: blur
2) Remark: blur
3) Remark: blur

Cross Reference

Material Name Country Standard
AA 6101B USA International Registration Record (AA)
3.5454.00 Yugoslavia JUS C.C2.100
AlMgSi0,5E Yugoslavia JUS C.C2.100
E-AlMgSi0,5 Switzerland SN 210900
E-AlMgSi0,5 Turkey TS 412
AlSiMg E Hungary MSZ 3714/1
A96101 USA UNS
E-AlMgSi0,5 (3.3207) Germany DIN 1725-1

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur
blur blur
blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur
blur blur blur blur
blur blur blur blur
blur blur blur blur

Designation

Designation Material number Source
blur blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Similar Materials

Diagram Settings
Diagram Preview
Select properties and click "Preview Diagram"