EN AW-Al 99,98 | EN AW-1098 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full Access Best valueMaterial Description
| Material Number | Material Name | Material Number (single) | Standard | Scope | Standard Status | Country | Predecessor | Successor | VDA 231-106 classification | |
|---|---|---|---|---|---|---|---|---|---|---|
| EN AW-1098 (DIN EN 573-3 : 2007-11) | EN AW-Al 99,98 | EN AW-1098 | DIN EN 573-3 : 2007-11 | DIN EN 573-3 : 2007-11 replaced by DIN EN 573-3 : 2009-08 | Replaced | Germany | EN AW-Al 99,98 | EN AW-Al 99,98 | 2.1 | 1) |
| 1) Remark: Material EN AW-Al 99,98 is produced in large quantities for wire and prewire for mechanical application as well as for center punching. It is used in limited amount for sheets, bands and plates, rolled bars as well as for wire and prewire for welding applications. It is food-safe. The material is comparable to the trademark Al99,98R, material number 3.0385, acc. to DIN 1712-3 : 1976-12. EN AW-Al 99,98 is an extremely pure aluminium material with particularly high electrical conductivity. This material is very well anodic oxidizable (high gloss finished surfaces), but it shows only low mechanical strength. It is unsuitable for machining (greasing), however it is well weldable and solderable. Formability and corrosion behavior in acid sphere are very good. Application: e.g. for pressure gas tanks, for chemical and food industry, for household articles, reflectors, decorative strips, costume jewelry, for etching band, electrolyte condensers as well as for feederflags. |
Chemical Composition
| Cu [%] | Fe [%] | Si [%] | Ti [%] | Zn [%] | Remainder | |
|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | ||||||
| 2) Remark: blur |
Material Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
Mechanical Properties
| Semi-finished Product | Condition | Delivery Condition EN | Nominal Size [mm] | Temperature [°C] | Tensile Strength [MPa] | Yield Strength (0.2% offset) [MPa] | Elongation A100 [%] | |
|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | 1) | |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| 1) Source: blur |
Producer/Supplier/Trade names
| Tradename | Supplier |
|---|---|
| EN AW-1098 | Drahtwerk Elisental W. Erdmann GmbH & Co, Neuenrade |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur |
Linear-elastic
| Temperature [°C] | Young's modulus [GPa] | Bulk modulus [GPa] | Shear modulus [GPa] | Poisson's ratio |
|---|---|---|---|---|
| blur | blur | |||
| blur | blur | |||
| blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Alternating stress
| Temperature [°C] | Stress ratio | Mean stress [MPa] | Alternating stress [MPa] | Cycles |
|---|---|---|---|---|
| blur | blur | blur | blur | |
| blur | blur | blur | blur | |
| blur | blur | blur | blur | |
| blur | blur | blur | blur |
Designation
| Designation | Material number | Source |
|---|---|---|
| blur | blur | blur |
| blur | blur | |
| blur | blur | |
| blur | blur | |
| blur | blur | |
| blur | blur | |
| blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |