DC07 | 1.0898 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full Access Best valueMaterial Description
| Material Number | Material Name | Material Number (single) | Standard | Scope | Standard Status | Country | VDA 231-106 classification | |
|---|---|---|---|---|---|---|---|---|
| 1.0898 (DIN EN 10130 : 2007-02) | DC07 | 1.0898 | DIN EN 10130 : 2007-02 | Supersedes DIN EN 10130 : 1999-02 | Valid | Germany | 1.1.1 | 1) |
| 1) Remark: The micro-alloyed steel DC07 is suitable for highest deformation demands and complex cold formed construction components. Products made of DC07 do not show any stretcher lines, this applies for the cold rerolled condition and the not cold rerolled condition. Welding: The steel is weldable with standard welding methods, but the method should be specified in the order. In the case of gas welding this information is necessary. The steel acts as substrate for surface refined and coated strip and sheet. Application: civil engineering, car manufacturing, traffic system |
Chemical Composition
| C [%] | Mn [%] | P [%] | S [%] | Ti [%] | Remainder | |
|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | ||||||
| 2) Remark: blur |
Material Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
Mechanical Properties
| Semi-finished Product | Condition | Nominal Size [mm] | Temperature [°C] | Tensile Strength [MPa] | Yield Strength [MPa] | Elongation A80 [%] | Vertical Anisotropy r90 | Hardening Exponent n90 | |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | |||||||||
| 2) Remark: blur |
Producer/Supplier/Trade names
| Tradename | Supplier |
|---|---|
| ArcelorMittal 07 | ArcelorMittal Commercial Germany, Cologne |
| DC07 | Salzgitter Flachstahl GmbH, Salzgitter |
| DC 07 | ThyssenKrupp Steel Europe AG, Duisburg |
| DC07 | Swiss Steel International GmbH, Düsseldorf |
| DC07 | HEINE + BEISSWENGER Stiftung + Co.KG, Fellbach |
| DC07 | pauly STAHLHANDEL, Essen |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur |
Linear-elastic
| Temperature [°C] | Young's modulus [GPa] | Bulk modulus [GPa] | Shear modulus [GPa] | Poisson's ratio |
|---|---|---|---|---|
| blur | blur | |||
| blur | blur | |||
| blur | blur | |||
| blur | blur | |||
| blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Alternating stress
| Temperature [°C] | Stress ratio | Mean stress [MPa] | Alternating stress [MPa] | Cycles |
|---|---|---|---|---|
| blur | blur | blur | blur | |
| blur | blur | blur | blur | |
| blur | blur | blur | blur |
Designation
| Designation | Material number | Source |
|---|---|---|
| blur | blur | blur |
| blur | blur | |
| blur | blur | |
| blur | blur | |
| blur | blur | |
| blur | blur | |
| blur | blur | |
| blur | blur | |
| blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |