Materials Portal Logo MATERIALS PORTAL

DC03 | 1.0347 Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access

Material Description

Material Number Material Number (single) Standard Range of Application Standard Status Country Successor
1.0347 (DIN EN 10130 : 1999-02) 1.0347 DIN EN 10130 : 1999-02 DIN EN 10130 : 1999-02 replaced by DIN EN 10130 : 2007-02 Replaced Germany DC03 1)
1) Remark: The non-alloy steel DC03 acc. to DIN EN 10130 is suitable for cold forming of simple profile forms and components. Mechanical foldings are possible for thicknesses of up to 1,5 mm. To freedom of stretcher strains applies a period of 3 months after provision of the products for surface type A and B. Welding: DC03 is weldable by the following welding methods: MAG (metal-active-gas), plasma welding, laser welding, compression weld welding, resistance welding (spot, roll weld, buckle welding), arc welding. The steel acts as substrate for surface refined and coated bands and sheets. Application of DC03: household appliances industry, construction trade, car manufacturing, traffic system. Acc. to DIN EN 10139 DC03 is offered as cold rolled band or bar, cut in strength range HK270 to HK590. On welding of DC03 in condition HK290 to HK590 has to be considered the potential influence to the mechanical properties

Chemical Composition

C [%] Mn [%] P [%] S [%]
blur blur blur blur 1)
1) Source: blur

Mechanical Properties

Semi-finished Product Condition Nominal Size [mm] Temperature [°C] Tensile Strength [MPa] Yield Strength [MPa] Elongation A80 [%] Vertical Anisotropy r90
blur blur blur blur blur blur blur blur 1)2)
1) Source: blur
2) Remark: blur

Cross Reference

Material Name Country Standard
E France NF A 36-401
CR 3 Great Britain BS 1449-1
FeP02 Italy UNI 5866
SPCD Japan JIS G 3141
1146 Sweden MNC 915
AP02 Spain UNE 36086
CS Type A, B or C USA ASTM A 1008
RRSt 13 Germany DIN 1623-1

Material Compliance

REACh RoHS
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Designation

Designation Material number Source
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur