Compare Plastics, Metals, and More for Construction, Design, and Simulation - Materials Portal

CuNi2Si | CW111C Material Datasheet

Material Standard Values
Material Models for Simulation

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access

Material Description

Material Number	Material Number (single)	Standard	Range of Application	Standard Status	Country	Predecessor	Successor
CW111C (DIN EN 12167 : 2011-08)	CW111C	DIN EN 12167 : 2011-08	DIN EN 12167 : 2011-08 replaced by DIN EN 12167 : 2016-11	Replaced	Germany	CuNi2Si	CuNi2Si	1)
1) Remark: CuNi2Si, mat. No CW111C, is counted among hardenable, low alloyed copper alloys. To the comparable make CuBNi2Si, mat. No 2.0855, acc. to DIN 17666 : 1983-12 applies: The material shows favorable electrical and thermal conductivity, corrosion resistance, high fatigue and creep resistance as well as favorable spring properties. CuNi2Si is in hardened condition resistant to stress corrosion. Temperature for removal of workhardening approximates 450°C. Strength still increases at low-temperature range. Processing properties: hot and cold forming: good machinability: moderately soft soldering: good hard soldering: moderately gas shielded welding: moderately burnishing: good Application: Particularly for aerial line material, such as clamps, mounting links, nuts, high-strength and corrosion resistant screws. Furthermore for wire ropes in electrical overhead line construction, bearing bushings, roller bearing cages, valve guide bushings and springs. For the electrolytically tinned strip the coatings (Sn bright, Sn matt, Sn fuzed, SnPb) are listed by the application (better solderability, better corrosion resistance, reduction of the electrical contact resistance, better appearance) in the DIN EN 14436 : 2004-11 (Table 5)

Chemical Composition

Fe [%]	Mn [%]	Ni [%]	Pb [%]	Si [%]
blur	blur	blur	blur	blur	1)2)
1) Source: blur
2) Remark: blur

Mechanical Properties

Semi-finished Product	Strength Abbrevation	Nominal Size [mm]	Temperature [°C]	Tensile Strength [MPa]	Yield Strength (0.2% offset) [MPa]	Elongation A100 [%]	Elongation A11,3 [%]	Elongation A [%]	Hardness HB \| HBW
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
1) Source: blur

Physical Properties

Condition	Temperature [°C]	Melting Temperature [°C]	Density [g/cm³]	Young's Modulus [GPa]	Poisson's Ratio	Mean Coefficient of Thermal Expansion [10^-6*K^-1]	Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1]	Thermal Conductivity [W/(m*K)]	Mean Specific Heat Capacity [kJ/(kg*K)]	Electric Conductivity [MS/m]	Specific Electric Conductivity [% IACS]
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	2)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	3)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	3)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	4)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	4)
1) Source: blur
2) Source: blur
3) Source: blur
4) Source: blur

Heat Treatment

Heat Treatment	Temperature [°C]
blur	blur	1)
blur	blur	1)
blur	blur	1)
1) Source: blur

Cross Reference

Material Name	Country	Standard
CuNi2Si	Europe	EN 12167
CuNi2Si	International	ISO 1187	1)
C18000	USA	UNS	1)
C64700	USA	UNS	1)
B411 UNS C64700	USA	ASTM B411	1)
2.0855	Germany	DIN 17666	2)
CuNi2Si	Germany	DIN 17666	2)
1) Source: Deutsches Kupferinstitut Berufsverband e.V., Düsseldorf
2) Source: DIN CEN/TS 13388 (DIN SPEC 9700)

Producer/Supplier/Trade names

Tradename	Supplier
OF2400	OTTO FUCHS KG, Meinerzhagen
4720	VDM Metals GmbH, Frankfurt/Main
Coradur 2	Wieland Prometa GmbH, Düsseldorf
CuNi2Si	CSN Carl Schreiber GmbH, Neunkirchen
CuNi2Si	Schreier Metall GmbH, Erkrath
CuNi2Si	Wieland Prometa GmbH, Düsseldorf
CuNi2Si	Auerhammer Vacuumgießerei GmbH, Aue
Kuprodur A	VDM Metals GmbH, Frankfurt/Main
NSB	ZOLLERN GmbH & Co. KG, Sigmaringen

Material Compliance

REACh	RoHS
blur	blur

Linear-elastic

Temperature [°C]	Young's modulus [GPa]	Bulk modulus [GPa]	Shear modulus [GPa]	Poisson's ratio
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Coefficient thermal expansion

Related Temperature [°C]	Temperature [°C]	Coefficient thermal expansion [10^-6*K^-1]
blur	blur	blur

Specific heat

Temperature [°C]	Specific heat [kJ/(kg*K)]
blur	blur

Density

Temperature [°C]	Density [g/cm³]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Thermal conductivity

Temperature [°C]	Thermal conductivity [W/(m*K)]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Designation

Designation	Material number	Source
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Linear-elastic

Temperature [°C]	Young's modulus [GPa]	Bulk modulus [GPa]	Shear modulus [GPa]	Poisson's ratio
blur	blur	blur	blur	blur

Thermal conductivity

Temperature [°C]	Thermal conductivity [W/(m*K)]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur