CuAl10Fe3Mn2 | 2.0936 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full AccessMaterial Description
| Material Number | Material Name | Material Number (single) | Standard | Standard Status | Country | VDA 231-106 classification | |
|---|---|---|---|---|---|---|---|
| 2.0936 (DIN 17665 : 1983-12) | CuAl10Fe3Mn2 | 2.0936 | DIN 17665 : 1983-12 | Withdrawn without replacement | Germany | 3.2 | 1) |
| 1) Remark: CuAl10Fe3Mn2 (earlier CuAl10Fe) is a high strength wrought alloy, also at increased temperatures. The strength properties of the cold formable alloy are mainly influenced by the strain rate. The tensile strength, the yield strength and the hardness will increase and the elongation decrease with increasing cold forming rate. An strength between F60 and F70 is reachable. The electric conductivity and the heat conductivity of this grade decrease with increasing Al-content. CuAl5 is corrosion resistant to sea water, potash solution and mineral acids. CuAl10Fe3Mn2 has a high heat-resistance up to about 300 degrees C and a high fatigue strength, also under corrosion stress. The material is resistant to scaling, has a high wear resistance, a high corrosion resistance to salt water, sulphite lye and mineral acids. Processing properties: Hot forming: good Cold forming: poor Cutting: mid Brazing: mid Soft soldering: poor Gas-shielded welding: good Polishing: good Application: CuAl10Fe3Mn2 is a material for construction purpose for chemical apparatus engineering. Also especially applicable for shock loaded, vibration loaded or wear loaded parts in the engine and gearbox engineering, for scale resistant parts, bolts, high strength screws and nuts, shafts, spindles, worm gears, toothed wheels, wheel rims, controller parts in the hydraulic as well as for bearing and slide elements. |
Chemical Composition
| Al [%] | Fe [%] | Mn [%] | Ni [%] | Pb [%] | Zn [%] | Remainder | |
|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | |||||||
| 2) Remark: blur |
Material Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
Mechanical Properties
| Semi-finished Product | Condition | Condition Number | Strength Abbrevation | Nominal Size [mm] | Temperature [°C] | Tensile Strength [MPa] | Yield Strength (0.2% offset) [MPa] | Elongation A [%] | Hardness HB | HBW | |
|---|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 1)3) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 4)5) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 4)5) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 3)4) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 3)4) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 3)4) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 3)4) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 6)7) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 6)7) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 6)7) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 8)9) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 8)9) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 8)9) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 8)9) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 8)9) |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 8)9) |
| 1) Source: blur | ||||||||||
| 2) Remark: blur | ||||||||||
| 3) Remark: blur | ||||||||||
| 4) Source: blur | ||||||||||
| 5) Remark: blur | ||||||||||
| 6) Source: blur | ||||||||||
| 7) Remark: blur | ||||||||||
| 8) Source: blur | ||||||||||
| 9) Remark: blur |
Physical Properties
| Temperature [°C] | Melting Temperature [°C] | Density [g/cm³] | Young's Modulus [GPa] | Shear Modulus [GPa] | Thermal Conductivity [W/(m*K)] | Mean Specific Heat Capacity [kJ/(kg*K)] | Electric Conductivity [MS/m] | |
|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| 1) Source: blur |
Creep Rupture Behaviour
| Condition | Temperature [°C] | Creep Tensile Strength at 10³ h [MPa] | 0.1% Creep Limit at 10³ h [MPa] | |
|---|---|---|---|---|
| blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | 1) |
| 1) Source: blur |
Cross Reference
| Material Name | Country | Standard | |
|---|---|---|---|
| 423046 | Czech Republik/Slovakia | CSN 423046 | |
| CuAl10Fe3Mn1,5 | Czech Republik/Slovakia | CSN 423046 | |
| CA 103 | Great Britain | BS 2874 | |
| BrAZhMc10-3-1,5 | Russia | GOST 18175-78 | |
| CuAl10Fe3 | International | ISO 428-83 | |
| BA1032 | Poland | PN-77/H-87050 | |
| CuAl10Fe3 | Romania | STAS 203-80 | |
| CuAl10Fe3Mn1 | Hungary | MSZ 711/1-77 | |
| C62300 | USA | ASTM B 124 | |
| C62300 | USA | ASTM B 150 | |
| CuAl10Fe3Mn2 (CW306G) | Germany | DIN EN 12165 | |
| CuAl10Fe3Mn2 (CW306G) | Germany | DIN EN 12167 | |
| CuAl10Fe3Mn2 (CW306G) | Germany | DIN EN 12163 | |
| CuAl10Fe3Mn2 (CW306G) | Germany | DIN EN 12420 | |
| AlBz10Fe | Germany | 1) | |
| 1) Source: DIN 1755-1 |
Producer/Supplier/Trade names
| Tradename | Supplier |
|---|---|
| 2231 | OTTO FUCHS KG, Meinerzhagen |
| 4500 | VDM Metals GmbH, Frankfurt/Main |
| AB 3 S | Wieland Metal Services Germany GmbH, Düsseldorf |
| Aeterna WF 26 | VDM Metals GmbH, Frankfurt/Main |
| AMB 1 | ZOLLERN GmbH & Co. KG, Sigmaringen |
| CuAl10Fe3Mn2 | CSN Carl Schreiber GmbH, Neunkirchen |
| CuAl10Fe3Mn2 | Schreier Metall GmbH, Erkrath |
| CuAl10Fe3Mn2 | Wieland Metal Services Germany GmbH, Düsseldorf |