Compare Plastics, Metals, and More for Construction, Design, and Simulation

AlMgSi0,7 | 3.3210 Material Datasheet

Material Standard Values
Material Models for Simulation

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Material Description

Material Number	Material Number (single)	Standard	Scope	Standard Status	Country	Successor	VDA 231-106 classification
3.3210 (DIN 1725-1 : 1983-02)	3.3210	DIN 1725-1 : 1983-02	DIN 1725-1 : 1983-02 replaced by DIN EN 573-3 : 2003-10 and DIN EN 573-4 : 2004-05	Replaced	Germany	EN AW-Al SiMg(A)	2.1	1)
1) Remark: This cold and hot hardenable material reaches mechanical properties from 200 to 250 MPa with A5-elongations at break of approx. 10 %. In warm and cold-hardened condition is this alloy only limited ductile, in the soft material condition however well. The Weldability, the corrosion resistance and the ability for anodising are good. However this alloy is used more for rivet or bolt joints, because of the destabilization arising within the welding seam range. Heat treatment for hardening: solution annealing: 525 to 540 °C, quenching on air or in water cold ageing: 5 to 8 d at ambient temperature hot ageing: 4 to 16 h at 155 to 190 °C Application: In the construction of vehicles for vehicle floors, bordwaende, stands, commercial motor vehicle superstructures of all kinds, trim. In the building industry for window, doors, window walls, shower cubicles, fences. In the building of rail-mounted vehicles for car boxes. In shipbuilding for sail masts, sail trees. In mechanical engineering (including building of forms) and for metal goods (e.g. building fittings, table-ware, flow pressed parts, reflectors).

Chemical Composition

Cr [%]	Cu [%]	Fe [%]	Mg [%]	Mn [%]	Si [%]	Ti [%]	Zn [%]
blur	blur	blur	blur	blur	blur	blur	blur	1)2)
1) Source: blur
2) Remark: blur

Mechanical Properties

Semi-finished Product	Condition	Designation of the delivered Condition DIN	Strength Abbrevation	Nominal Size [mm]	Temperature [°C]	Tensile Strength [MPa]	Yield Strength (0.2% offset) [MPa]	Elongation A10 [%]	Elongation A [%]	Hardness HB \| HBW
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	2)
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	1)
1) Source: blur
2) Source: blur

Physical Properties

Temperature [°C]	Melting Temperature [°C]	Density [g/cm³]	Young's Modulus [GPa]	Shear Modulus [GPa]	Thermal Conductivity [W/(m*K)]	Electric Conductivity [MS/m]
blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	2)3)
blur	blur	blur	blur	blur	blur	blur	2)
1) Source: blur
2) Source: blur
3) Remark: blur

Cross Reference

Material Name	Country	Standard
6005A	France	NF A 50-411
A-SG0,5	France	NF A 50-411
AlMgSi0,7	USA	AA 6005A
AlSiMg(A)	International	ISO 209-1
6005A	Italy	UNI 9006/6
9006/6	Italy	UNI 9006/6
P-AlMg0,6Si0,7MnCr	Italy	UNI 9006/6
144107	Sweden	MNC 40
144107	Sweden	SIS 144107
AlMgSi0,7	Switzerland	SN 210900
6005A	Spain	UNE 38-300
Al-0,7SiMg	Spain	UNE 38-300
L-3454	Spain	UNE 38-300
6005A	Spain	UNE 38-349
Al-0,7SiMg	Spain	UNE 38-349
L-3454	Spain	UNE 38-349
EN AW-Al SiMg(A) (EN AW-6005A)	Germany	DIN EN 573-3

Producer/Supplier/Trade names

Tradename	Supplier
426	Erbslöh Aluminium GmbH, Velbert
6070	Erbslöh Aluminium GmbH, Velbert
AlMgSi0,7	Wieland Metal Services Germany GmbH, Düsseldorf
AlMgSi0,7 F25	Hydro Aluminium Extrusion Deutschland GmbH, Rackwitz
AlMgSi0,7 F26	Hydro Aluminium Extrusion Deutschland GmbH, Rackwitz
AlMgSi0,7 F27	Hydro Aluminium Extrusion Deutschland GmbH, Rackwitz
AS 07	OTTO FUCHS KG, Meinerzhagen

Material Compliance

REACh	RoHS
blur	blur

Linear-elastic

Temperature [°C]	Young's modulus [GPa]	Bulk modulus [GPa]	Shear modulus [GPa]	Poisson's ratio
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur

Alternating stress

Temperature [°C]	Stress ratio	Mean stress [MPa]	Alternating stress [MPa]	Cycles
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Density

Temperature [°C]	Density [g/cm³]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Thermal conductivity

Temperature [°C]	Thermal conductivity [W/(m*K)]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Designation

Designation	Material number	Source
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

AlMgSi0,7 | 3.3210 Material Datasheet

Material Standard Values

Material Models for Simulation

Material Description

Chemical Composition

Mechanical Properties

Physical Properties

Cross Reference

Producer/Supplier/Trade names

Material Compliance

AlMgSi0,7 (3.3210; DIN 1725-1 : 1983-02)

Linear-elastic

Alternating stress

Yield strength

Density

Tensile strength

Thermal conductivity

Classification

Designation

AlMgSi0,7 (T8 (solution heat-treated, cold worked and artificially aged); section; 0.000-10.000mm)

Yield strength

Tensile strength

Classification

AlMgSi0,7 (T8 (solution heat-treated, cold worked and artificially aged); section; 0.000-6.000mm)

Yield strength

Tensile strength

Classification

AlMgSi0,7 (T8 (solution heat-treated, cold worked and artificially aged); section; 6.000-10.000mm)

Yield strength

Tensile strength

Classification

AlMgSi0,7 (T8 (solution heat-treated, cold worked and artificially aged); tube; 0.000-10.000mm)

Yield strength

Tensile strength

Classification