Compare Plastics, Metals, and More for Construction, Design, and Simulation - Materials Portal Logo MATERIALS PORTAL

AlMg4,5 | 3.3345 Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access Best value

Material Description

Material Number Material Name Material Number (single) Standard Scope Standard Status Country VDA 231-106 classification
3.3345 (DIN 1725-1 : 1983-02) AlMg4,5 3.3345 DIN 1725-1 : 1983-02 DIN 1725-1 : 1983-02 replaced by DIN EN 573-3 : 2003-10 and DIN EN 573-4 : 2004-05 Replaced Germany 2.1 1)
1) Remark: The alloy is characterised by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increases the strength, but the cold forming capacity decreases. The material is nature hard, i.e. only by a cold forming and not by a purposeful heat treatment a strength increase can be attained. It is well polishable and anodisable. The splinter-giving machinability becomes better with increasing Mg content, just as the weldability. The material is sensitive to intergranular corrosion. To inhibit the inclination of the intergranular corrosion in the technology a purposeful addition of Mn and/or Cr can be applied or an appropriate heat treatment, too. It is standardised as semi-finished material according to DIN 1788 as sheet metal and strip with max. 35 mm thickness). Application: Predominantly for packing (latch volume according to DIN 59606).

Chemical Composition

Cr [%] Cu [%] Fe [%] Mg [%] Mn [%] Si [%] Ti [%] Zn [%] Remainder
blur blur blur blur blur blur blur blur blur 1)2)
1) Source: blur
2) Remark: blur

Material Compliance

REACh RoHS
blur blur

Mechanical Properties

Semi-finished Product Condition Designation of the delivered Condition DIN Delivery Condition EN Strength Abbrevation Nominal Size [mm] Temperature [°C] Tensile Strength [MPa] Yield Strength (0.2% offset) [MPa] Elongation A10 [%]
blur blur blur blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur blur blur blur 2)
blur blur blur blur blur blur blur blur blur blur 2)
1) Source: blur
2) Source: blur

Physical Properties

Temperature [°C] Melting Temperature [°C] Density [g/cm³] Young's Modulus [GPa] Shear Modulus [GPa] Thermal Conductivity [W/(m*K)] Mean Specific Heat Capacity [kJ/(kg*K)] Electric Conductivity [MS/m]
blur blur blur 1)
blur blur blur blur blur 2)3)
blur 2)
1) Source: blur
2) Source: blur
3) Remark: blur

Formability - Bending - Folding

Condition Number Strength Abbrevation Nominal Size [mm] Rolling Direction Ductility Bend Factor
blur blur blur blur blur blur 1)2)
blur blur blur blur blur blur 1)
1) Source: blur
2) Remark: blur

Cross Reference

Material Name Country Standard
5052 Australia AS 2848.1
5082 France NF A 50-481
A-G4,5 France NF A 50-481
AlMg4,5 USA AA 5082
A5082P Japan JIS H 4000
AlMg4,5 Turkey TS 412
EN AW-Al Mg4,5 (EN AW-5082) Germany DIN EN 573-3

Producer/Supplier/Trade names

Tradename Supplier
AlMg4,5 Wieland Metal Services Germany GmbH, Düsseldorf

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur

Density

Temperature [°C] Density [g/cm³]
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur
blur blur
blur blur
blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur
blur blur blur blur
blur blur blur blur
blur blur blur blur

Specific heat

Temperature [°C] Specific heat [kJ/(kg*K)]
blur blur

Thermal conductivity

Temperature [°C] Thermal conductivity [W/(m*K)]
blur blur

Designation

Designation Material number Source
blur blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Similar Materials

Diagram Settings
Diagram Preview
Select properties and click "Preview Diagram"