Compare Plastics, Metals, and More for Construction, Design, and Simulation - Materials Portal Logo MATERIALS PORTAL

AlMg1,8 | 3.3326 Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access Best value

Material Description

Material Number Material Name Material Number (single) Standard Scope Standard Status Country Successor VDA 231-106 classification
3.3326 (DIN 1725-1 : 1983-02) AlMg1,8 3.3326 DIN 1725-1 : 1983-02 DIN 1725-1 : 1983-02 replaced by DIN EN 573-3 : 2003-10 and DIN EN 573-4 : 2004-05 Replaced Germany EN AW-Al Mg2(B) 2.1 1)
1) Remark: The alloy is characterised by a good corrosion resistance. It is sea water steady and resistant to saline atmosphere. The Mg content increases the strength, but the cold forming capacity decreases. The material is nature hard, i.e. only by a cold forming and not by a purposeful heat treatment a strength increase can be attained. It is well polishable and anodisable. The splinter-giving machinability becomes better with increasing Mg content, just as the weldability. From the AlMg alloys the mark AlMg1,5 has to exhibit only relatively small mechanical properties. Standardised semi-finished material only for tubes in accordance to DIN 1746 and for extruded profiles according to DIN 1748. Application: Ferrules for wires rope in accordance to DIN 3093. In the civil engineering for carrying constructions, for transport containers. In electro-technology for antennas and parabolic reflectors.

Chemical Composition

Cr [%] Cu [%] Fe [%] Mg [%] Mn [%] Si [%] Ti [%] Zn [%] Remainder
blur blur blur blur blur blur blur blur blur 1)2)
1) Source: blur
2) Remark: blur

Material Compliance

REACh RoHS
blur blur

Mechanical Properties

Semi-finished Product Condition Designation of the delivered Condition DIN Delivery Condition EN Strength Abbrevation Nominal Size [mm] Temperature [°C] Tensile Strength [MPa] Yield Strength (0.2% offset) [MPa] Elongation A10 [%] Elongation A [%] Hardness HB | HBW
blur blur blur blur blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur blur blur blur blur blur 2)
blur blur blur blur blur blur blur blur blur blur blur blur 2)
blur blur blur blur blur blur blur blur blur blur blur blur 2)3)
blur blur blur blur blur blur blur blur blur blur blur blur 2)4)
1) Source: blur
2) Source: blur
3) Remark: blur
4) Remark: blur

Physical Properties

Temperature [°C] Melting Temperature [°C] Density [g/cm³] Young's Modulus [GPa] Shear Modulus [GPa] Thermal Conductivity [W/(m*K)] Mean Specific Heat Capacity [kJ/(kg*K)] Electric Conductivity [MS/m]
blur 1)
blur blur blur blur blur blur 1)
blur blur 2)
1) Source: blur
2) Source: blur

Formability - Bending - Folding

Rolling Direction Ductility
blur blur 1)
1) Source: blur

Cross Reference

Material Name Country Standard
AlMg1,8 USA AA 5051A
AlMg1,8 Turkey TS 412
EN AW-Al Mg2(B) (EN AW-5051A) Germany DIN EN 573-3

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur

Density

Temperature [°C] Density [g/cm³]
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur
blur blur
blur blur
blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur
blur blur blur blur
blur blur blur blur
blur blur blur blur

Specific heat

Temperature [°C] Specific heat [kJ/(kg*K)]
blur blur

Thermal conductivity

Temperature [°C] Thermal conductivity [W/(m*K)]
blur blur

Designation

Designation Material number Source
blur blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Similar Materials

Diagram Settings
Diagram Preview
Select properties and click "Preview Diagram"