StE 420 | 1.8902 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full AccessMaterial Description
| Material Number | Material Number (single) | Standard | Range of Application | Standard Status | Country | Remark | Application temperature [°C] |
|---|---|---|---|---|---|---|---|
| 1.8902 (DIN 17102 : 1983-10) | 1.8902 | DIN 17102 : 1983-10 | DIN 17102 : 1983-10 replaced by DIN EN 10025-1/-3 : 2005-02, DIN EN 10028-1/-3 : 2003-09 | Replaced | Germany | The fine grained steel StE 420 is used for welded constructions of different kind like pressure vessels, stationary or mobile storage tanks, high pressure lines, bridge and support constructions etc. The lowest application temperature amounts to -20 °C. | ≥ -20 |
Chemical Composition
| Al [%] | C [%] | Cr [%] | Cu [%] | Mn [%] | Mo [%] | N [%] | Nb [%] | Ni [%] | P [%] | S [%] | Si [%] | V [%] | Source | Remark |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
Mechanical Properties
| Semi-finished Product | Condition | Nominal Size [mm] | Temperature [°C] | Specimen Direction | Tensile Strength [MPa] | Yield Strength [MPa] | Elongation A [%] | Source | Remark |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
Physical Properties
| Temperature [°C] | Density [g/cm³] | Young's Modulus [GPa] | Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] | Differential Coefficient of Thermal Expansion [10^-6*K^-1] | Thermal Conductivity [W/(m*K)] | Thermal Diffusivity [10^-6 m²/s] | Specific Electrical Resistance [µΩm] | Mean Specific Heat Capacity [kJ/(kg*K)] | True Specific Heat Capacity [kJ/(kg*K)] | Source |
|---|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
Young's Modulus [GPa] vs Temperature [°C]
Exclusive Insight Locked!
This premium diagram is currently blurred. Gain full access to detailed insights and stay ahead with exclusive content.
Unlock NowMean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] vs Temperature [°C]
Exclusive Insight Locked!
This premium diagram is currently blurred. Gain full access to detailed insights and stay ahead with exclusive content.
Unlock NowDifferential Coefficient of Thermal Expansion [10^-6*K^-1] vs Temperature [°C]
Exclusive Insight Locked!
This premium diagram is currently blurred. Gain full access to detailed insights and stay ahead with exclusive content.
Unlock NowToughness Data (Impact)
| Semi-finished Product | Condition | Nominal Size [mm] | Temperature [°C] | Specimen Shape | Specimen Direction | Notch Impact Energy [J] | Source |
|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur | blur | blur | blur |
Heat Treatment
| Heat Treatment | Temperature [°C] | Source | Remark |
|---|---|---|---|
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
Cross Reference
| Material Name | Country | Standard |
|---|---|---|
| E 420 R | France | NF A 36-201 |
| Class 2 | USA | ASTM A 537 |
| S420N | Germany | DIN EN 10025-3 |
Producer/Supplier/Trade names
| Tradename | Supplier |
|---|---|
| Aldur E 43 | voestalpine AG, Linz |
| Dillinal 55/43 | AG der Dillinger Hüttenwerke, Dillingen |
| DIRO-StE 420 | DIROSTAHL, Remscheid |
| FG 43 | Vallourec Deutschland GmbH, Mülheim |
| Histar 420 | Carl Spaeter GmbH, Oberhausen |
| S420N | Hoesch Hohenlimburg GmbH, Hagen |
| S420N | ThyssenKrupp Steel Europe AG, Duisburg |
| S420N | Georgsmarienhütte GmbH, Georgsmarienhütte |
| S420N | Hayes-Lemmerz-Werke GmbH, Königswinter |
| S420N | BGH Edelstahlwerke GmbH, Freital |
| S420N | Schmiedewerke Gröditz GmbH, Gröditz |
| SB 43 FG | Salzgitter Flachstahl GmbH, Salzgitter |
Material Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
FKM Guideline Fatigue Strength
| Semi-finished Product | Condition | Nominal Size [mm] | Tensile Strength [MPa] | Yield Strength [MPa] | Fatigue Limit under rev. Tension-Compression Stresses [MPa] | Fatigue Strength under pulsating Tensile Stresses [MPa] | Bending Fatigue Strength [MPa] | Shear Fatigue Strength [MPa] | Torsion Fatigue Strength [MPa] | Constant a for size factor Kd for yield stress Rp | Constant a for size factor Kd for tensile strength Rm | Source | Remark |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
StE 420 (1.8902; DIN 17102 : 1983-10)
Linear-elastic
| Temperature [°C] | Young's modulus [GPa] | Poisson's ratio |
|---|---|---|
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
Alternating stress
| Temperature [°C] | Stress ratio | Alternating stress [MPa] | Cycles |
|---|---|---|---|
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Electrical resistivity
| Temperature [°C] | Specific electrical resistance [µΩm] |
|---|---|
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
Coefficient thermal expansion
| Related Temperature [°C] | Temperature [°C] | Coefficient thermal expansion [10^-6*K^-1] |
|---|---|---|
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
Specific heat
| Temperature [°C] | Specific heat [kJ/(kg*K)] |
|---|---|
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
Density
| Temperature [°C] | Density [g/cm³] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Thermal conductivity
| Temperature [°C] | Thermal conductivity [W/(m*K)] |
|---|---|
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
| blur | blur |
Classification
| WIAM Material | Source description |
|---|---|
| blur | blur |
Designation
| Designation | Material number | Source |
|---|---|---|
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
StE 420 (normalized or normalized formed (+N); tube; 0.000-12.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (cold worked, welded and normalized; section; 0.000-12.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (hot worked, normalized; section; 0.000-12.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 0.000-16.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); tube; 12.000-20.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (cold worked, welded and normalized; section; 12.000-20.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (hot worked, normalized; section; 12.000-20.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 16.000-35.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); tube; 20.000-40.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (cold worked, welded and normalized; section; 20.000-40.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (hot worked, normalized; section; 20.000-40.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 35.000-50.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); tube; 40.000-50.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (cold worked, welded and normalized; section; 40.000-50.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (hot worked, normalized; section; 40.000-50.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 50.000-60.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); tube; 50.000-65.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (cold worked, welded and normalized; section; 50.000-65.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (hot worked, normalized; section; 50.000-65.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 60.000-70.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 70.000-85.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 85.000-100.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 100.000-125.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); Large I , H, U shaped sections; 125.000-150.000mm)
Yield strength
| Temperature [°C] | Yield strength [MPa] |
|---|---|
| blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |
StE 420 (normalized or normalized formed (+N); bar; 40.000mm)
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| Treatment | Semi-finished product | Dimension [mm] | Source description |
|---|---|---|---|
| blur | blur | blur | blur |