S275NL | 1.0491 Material Datasheet

Material Test Series Values

Material Standard Values

Material Models for Simulation

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Material Description

Material Number	Material Number (single)	Standard	Range of Application	Standard Status	Country	Remark
1.0491 (DIN EN 10113-2 : 1993-04)	1.0491	DIN EN 10113-2 : 1993-04	DIN EN 10113-2 : 1993-04 replaced by DIN EN 10025-3 : 2005-02	Replaced	Germany	S275NL is a weldable fine-grained steel with a min. yield point of 275 N/mm². The steel is applicated in normalized condition for several types of welded constructions such as fixed and movable storage container, high-pressure pipes, bridge and load-bearing constructions etc. Application limit: at -50°C is warranted a notch impact energy of 27J (longitudinal test specimen). The carbon equivalent (by arrangement) amounts to: for nominal size: < 63 mm: 0,40% > 63 < 100 mm: 0,40% > 100 < 150 mm: 0,42% Cold forming: Suitability for cold bending, folding, cold flanging or cold welting has to be agreed. For sheet, strip and wide flat steel in normalized condition, for nominal thickness (s) up to 16 mm can be warranted the following bending radius values: longitudinal: 2,5 x s transverse: 2,0 x s Sheet and strip of nominal thicknesses < 8 mm for cold forming of sections is available on arrangement (e.g. for production of hollow sections). Surface refineability: S275NL has to be suitable by arrangement for hot galnanizing and it has to meet the appropriate product quality requirements.

Chemical Composition

Al [%]	C [%]	Cr [%]	Cu [%]	Mn [%]	Mo [%]	N [%]	Nb [%]	Ni [%]	P [%]	S [%]	Si [%]	Ti [%]	V [%]	Source	Remark
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Mechanical Properties

Semi-finished Product	Condition	Nominal Size [mm]	Temperature [°C]	Tensile Strength [MPa]	Yield Strength [MPa]	Elongation A [%]	Source	Remark
blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur	blur

Toughness Data (Impact)

Condition	Nominal Size [mm]	Temperature [°C]	Specimen Shape	Specimen Direction	Notch Impact Energy [J]	Source	Remark
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur	blur	blur

Heat Treatment

Heat Treatment	Temperature [°C]	Source	Remark
blur	blur	blur	blur
blur	blur	blur	blur
blur	blur	blur	blur

Cross Reference

Material Name	Country	Standard
FeE 275 KTN	Italy	UNI
TStE 285	Germany	DIN 17102

Producer/Supplier/Trade names

Tradename	Supplier
Aldur E 29 T	voestalpine AG, Linz
Buderus TTStE 29	Buderus Edelstahl GmbH, Wetzlar
Dillinal 40/29 AT	AG der Dillinger Hüttenwerke, Dillingen
DIRO-TStE 285	DIROSTAHL, Remscheid
FG 29 T	Vallourec Deutschland GmbH, Mülheim
S275NL	ArcelorMittal Commercial Germany, Cologne
S275NL	Hoesch Hohenlimburg GmbH, Hagen
S275NL	ThyssenKrupp Steel Europe AG, Duisburg
S275NL	Georgsmarienhütte GmbH, Georgsmarienhütte
S275NL	Hayes-Lemmerz-Werke GmbH, Königswinter
SB 29 FAK	Salzgitter Flachstahl GmbH, Salzgitter
TStE 285	Klöckner Stahl- und Metallhandel GmbH, Bremen

Material Compliance

REACh	RoHS
blur	blur

FKM Guideline Fatigue Strength

Semi-finished Product	Condition	Nominal Size [mm]	Tensile Strength [MPa]	Yield Strength [MPa]	Fatigue Limit under rev. Tension-Compression Stresses [MPa]	Fatigue Strength under pulsating Tensile Stresses [MPa]	Bending Fatigue Strength [MPa]	Shear Fatigue Strength [MPa]	Torsion Fatigue Strength [MPa]	Constant a for size factor Kd for yield stress Rp	Constant a for size factor Kd for tensile strength Rm	Source	Remark
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Formability - Bending - Folding

Condition	Nominal Size [mm]	Rolling Direction	Ductility	Bend Factor	Source
blur	blur	blur	blur	blur	blur
blur	blur	blur	blur	blur	blur

S275NL (1.0491; DIN EN 10113-2 : 1993-04)

Linear-elastic

Temperature [°C]	Young's modulus [GPa]	Poisson's ratio
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur

Alternating stress

Temperature [°C]	Stress ratio	Alternating stress [MPa]	Cycles
blur	blur	blur	blur
blur	blur	blur	blur
blur	blur	blur	blur

Yield strength

Temperature [°C]	Yield strength [MPa]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Source description
blur	blur

Designation

Designation	Material number	Source
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur
blur	blur	blur

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 0.000-16.000mm)

Yield strength

Temperature [°C]	Yield strength [MPa]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 16.000-40.000mm)

Yield strength

Temperature [°C]	Yield strength [MPa]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 40.000-63.000mm)

Yield strength

Temperature [°C]	Yield strength [MPa]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 63.000-80.000mm)

Yield strength

Temperature [°C]	Yield strength [MPa]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 80.000-100.000mm)

Yield strength

Temperature [°C]	Yield strength [MPa]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 100.000-150.000mm)

Yield strength

Temperature [°C]	Yield strength [MPa]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

S275NL (normalized or normalized formed (+N); wide flat; 150.000-250.000mm)

Yield strength

Temperature [°C]	Yield strength [MPa]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

S275NL (normalized or normalized formed (+N); bar; 40.000mm)

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

Treatment	Semi-finished product	Dimension [mm]	Source description
blur	blur	blur	blur

S275NL | 1.0491 Material Datasheet

Material Test Series Values

Material Standard Values

Material Models for Simulation

Material Description

Chemical Composition

Mechanical Properties

Toughness Data (Impact)

Heat Treatment

Cross Reference

Producer/Supplier/Trade names

Material Compliance

FKM Guideline Fatigue Strength

Formability - Bending - Folding

S275NL (1.0491; DIN EN 10113-2 : 1993-04)

Linear-elastic

Alternating stress

Yield strength

Tensile strength

Classification

Designation

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 0.000-16.000mm)

Yield strength

Tensile strength

Classification

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 16.000-40.000mm)

Yield strength

Tensile strength

Classification

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 40.000-63.000mm)

Yield strength

Tensile strength

Classification

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 63.000-80.000mm)

Yield strength

Tensile strength

Classification

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 80.000-100.000mm)

Yield strength

Tensile strength

Classification

S275NL (normalized or normalized formed (+N); Large I , H, U shaped sections; 100.000-150.000mm)

Yield strength

Tensile strength

Classification

S275NL (normalized or normalized formed (+N); wide flat; 150.000-250.000mm)

Yield strength

Tensile strength

Classification

S275NL (normalized or normalized formed (+N); bar; 40.000mm)

Tensile strength

Classification

Similar Materials