Materials Portal Logo MATERIALS PORTAL

HX260LAD (+Z,+ZF,+ZA,+AZ,+AS) | 1.0929 Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access

Material Description

Material Number Material Number (single) Standard Range of Application Standard Status Country Successor
1.0929 (DIN EN 10292 : 2005-03) 1.0929 DIN EN 10292 : 2005-03 DIN EN 10292 : 2005-03 replaced by DIN EN 10292 : 2007-06 Replaced Germany HX260LAD (+Z,+ZF,+ZA,+AZ,+AS) 1)
1) Remark: The steel HX260LAD (X=roll condition, LA=low alloyed, D=hot-dip coatable) is producible with the following coatings: - HX260LA+Z (plating Zn) with coating weights (double-sided) of 100, 140, 200, 225 and 275 g/m² (100 g approximate 7,1 µm per side) - HX260LAD+ZF (plating Zn-Fe) with coating weights (double-sided) of 100 and 120 g/m² (100 g approximate 7,1 µm per side) - HX260LAD+ZA (plating Zn-Al) with coating weights (double-sided) of 095, 130, 185, 200 and 255 g/m² (95 g approximate 7,2 µm per side) - HX260LAD+AZ (plating Al-Zn) with coating weights (double-sided) of 100, 150 and 185 g/m² (100 g approximate 13,3 µm per side) - HX260LAD+AS (plating Al-Si) with coating weights (double-sided) of 060 and 080 g/m² (100 g approximate 17 µm per side) The hot dip galvanizing refined flat products are available by arrangement on ordering with different coating weights (also per side). Following surface protection types can be delivered: chemical passivated, oiled, chemical passivated and oiled, sealed, phosphated, phosphated and oiled. Mechanical properties are warranted for a period of 3 months for Bake-hardening steels and for a period of 6 months after provision of the products for all other sorts. The same terms are valid for freedom from stretcher strains (surface type B and C). It is suitable for usual welding methods. For higher coating weights on welding are where approppriate necessary special measures. Furthermore suitability for joining by sticking as well as for application of organic coatings. Application: household appliances industry, construction trade, electrical industry, furniture industry, car industry.

Chemical Composition

Al [%] C [%] Mn [%] Nb [%] P [%] S [%] Si [%] Ti [%]
blur blur blur blur blur blur blur blur 1)
1) Source: blur

Mechanical Properties

Semi-finished Product Condition Temperature [°C] Specimen Direction Tensile Strength [MPa] Yield Strength (0.2% offset) [MPa] Elongation A80 [%]
blur blur blur blur blur blur blur 1)2)
blur blur blur blur blur blur blur 1)2)
1) Source: blur
2) Remark: blur

Cross Reference

Material Name Country Standard
HX260LAD Europe EN 10346

Producer/Supplier/Trade names

Tradename Supplier
HX260LAD ThyssenKrupp Steel Europe AG, Duisburg
HX260LAD Salzgitter Flachstahl GmbH, Salzgitter
HX260LAD voestalpine AG, Linz

Material Compliance

REACh RoHS
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Designation

Designation Material number Source
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur