Materials Portal Logo MATERIALS PORTAL

EN AC-Al Si10Mg(a) | EN AC-43000 Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access

Material Description

Material Number Material Number (single) Standard Scope Standard Status Country Predecessor Successor VDA 231-106 classification
EN AC-43000 (DIN EN 1706 : 1998-06) EN AC-43000 DIN EN 1706 : 1998-06 DIN EN 1706 : 1998-06 replaced by DIN EN 1706 : 2013-12 Replaced Germany G-AlSi10Mg EN AC-Al Si10Mg(a) 2.1 1)
1) Remark: Material EN AC-AlSi10Mg(a) is produced as sand and chilled cast. It shows the following casting characteristics and properties: plasticity: excellent heat crack resistance: excellent pressure tightness: good workability (after heat-treatment): good to acceptable workability (casting condition): good corrosion resistance: good decorative anodic oxidation: not advisable weldability: excellent polishability: insufficient strength at room temperature: good strength at increased temp. (up to 200°C): acceptable ductility (impact strength): acceptable fatigue strength amounts 80 to 110 N/mm² ( best available casting method, values for vibration durability up to 50*10 hoch 6 cycles [Woehler diagram]). To the comparable DIN-mark G-AlSi10Mg, mat. No. 3.2381, acc. to DIN 1725-2 : 1986-02 applies: The material is a neareutectic alloy of favorable casting properties. It is heat-resistant and hardenable, its weldability is excellent. It is suitable for complex, thin-walled, pressure-tight, vibration resistant, impact loaded casting parts. Application: equipment, machine, vehicle, ship, apparatus engineering cases, finned bodies, brake pads.

Chemical Composition

Cu [%] Fe [%] Mg [%] Mn [%] Ni [%] Pb [%] Si [%] Sn [%] Ti [%] Zn [%]
blur blur blur blur blur blur blur blur blur blur 1)2)
1) Source: blur
2) Remark: blur

Mechanical Properties

Casting Method Condition Temperature [°C] Tensile Strength [MPa] Yield Strength (0.2% offset) [MPa] Elongation A50 [%] Hardness HB | HBW
blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur 1)
1) Source: blur

Physical Properties

Temperature [°C] Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] Thermal Conductivity [W/(m*K)] Electric Conductivity [MS/m]
blur blur blur blur 1)
blur blur blur blur 1)
1) Source: blur

Cross Reference

Material Name Country Standard
AlSi10Mg Belgium NBN P 21-101
424331 Czech Republik/Slovakia CSN 424331
EN AC-Al Si10Mg(a) Europe EN 1706
A-S10G France NF A 50-702
A-S10G France NF A 57-105
4535 India IS 202
4535 India IS 617
Al-Si10Mg International ISO 3522
AlSi10Mg Norway NS 17501
AlSi10Mg Austria ÖNORM M 3429
144253 Sweden MNC 41
144253 Sweden SIS 144253
AlSi10Mg Switzerland VSM 10895/14
Al-10SiMg Spain UNE 38-256
L-2560 Spain UNE 38-256
Al-Si10Mg Turkey TS 410
ÖAlSi10Mg Hungary MSZ 3713
G-AlSi10Mg (3.2381) Germany DIN 1725-2

Producer/Supplier/Trade names

Tradename Supplier
G-AlSi10Mg Federal-Mogul Nürnberg GmbH, Nürnberg
G-AlSi10Mg Metallgießerei Ralf Mewes GmbH, Velbert
G-AlSi10Mg Rolf Andris GmbH, Villingen-Schwenningen
G-AlSi10Mg Olsberg Metallhandel Albert Honsel GmbH & Co. KG, Essen
G-AlSi10Mg Fehrmann Metallverarbeitung GmbH, Hamburg
Legierung 239 Gardner Denver Schopfheim GmbH, Schopfheim

Material Compliance

REACh RoHS
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Coefficient thermal expansion

Related Temperature [°C] Temperature [°C] Coefficient thermal expansion [10^-6*K^-1]
blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Thermal conductivity

Temperature [°C] Thermal conductivity [W/(m*K)]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Designation

Designation Material number Source
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur