Materials Portal Logo MATERIALS PORTAL

DX53D | 1.0355 Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access

Material Description

Material Number Material Number (single) Standard Range of Application Standard Status Country Predecessor Successor
1.0355 (DIN EN 10327 : 2004-09) 1.0355 DIN EN 10327 : 2004-09 DIN EN 10327 : 2004-09 replaced by DIN EN 10346 : 2009-07 Replaced Germany DX53D+Z/+ZF DX53D 1)
1) Remark: The alloyed high-grade steel DX53D (deep drawing quality) is deliverable with following hot-dip coatings: DX53D+Z (coating Zn), DX53D+ZF (coating Zn-Fe), DX53D+ZA (coating Zn-Al), DX53D+AZ (coating Al-Zn), DX53D+AS (coating Al-Si). The coating mass for Z amounts to 100, 140, 200, (225), 275 g/m², for ZF to 100, 120 and (140)** g/m², for ZA to 95, 130, 185, 200, 255 and 300* g/m², for AZ to 100, 150 and 185 g/m², for AS it amounts to 60, 80, 100, (120) und (150) g/m². The parenthesis values are deliverable after arrangement the values are in each case both side minimum values (three-faced specimen). The * marked values are not deliverable for the surface types B and C and the ** marked values are not deliverable for the surface type C (see also DIN EN 10327). The advantages in opposite to the hot-dip galvanising are: - higher corrosion resistance - excellent forming behaviour - low crack susceptibility of the coating The material is used for construction parts with good cold formability and high corrosion resistance. The coated steel is weldable with the usual methods. Furthermore are given the adhesive suitability and the coatability with organic materials, in each case after a previous suitable surface treatment. Application: household appliances industry, construction industry, furniture industry, electrical engineering, automotive engineering

Chemical Composition

C [%] Mn [%] P [%] S [%] Si [%] Ti [%]
blur blur blur blur blur blur 1)
1) Source: blur

Mechanical Properties

Semi-finished Product Condition Nominal Size [mm] Temperature [°C] Specimen Direction Tensile Strength [MPa] Yield Strength [MPa] Elongation A80 [%]
blur blur blur blur blur blur blur blur 1)2)
1) Source: blur
2) Remark: blur

Cross Reference

Material Name Country Standard
DX53D Europe EN 10346
GES France NF A 36-321
Z 5 Great Britain BS 2989
FeP0 5 G Italy UNI 5733
TH 05-Zn/TH 05-ZnFe Austria Wbl. VOEST-Alpine
DDS USA ASTM A 653
EDDS USA ASTM A 653
DS USA ASTM A 792
DDS USA ASTM A 875
EDDS USA ASTM A 875
St 05 Z Germany DIN 17162-1

Material Compliance

REACh RoHS
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Designation

Designation Material number Source
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur