Materials Portal Logo MATERIALS PORTAL

CuTeP | CW118C Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access

Material Description

Material Number Material Number (single) Standard Scope Standard Status Country Successor VDA 231-106 classification
CW118C (DIN EN 12164 : 2000-09) CW118C DIN EN 12164 : 2000-09 DIN EN 12164 : 2000-09 replaced by DIN EN 12164 : 2011-08 Replaced Germany CuTeP 3.2 1)
1) Remark: CuTeP, mat. No CW118C, is counted among unhardenable, low alloyed copper alloys. To the comparable make CuTeP, mat. No 2.1546, acc. to DIN 17666 : 1983-12 applies: A strength increase is achievable only by cold forming. CuTeP is applicated as free-cutting alloy due to its favorable machinability. The alloy shows a higher temperature for removal of workhardening (350°C) compared to pure copper. CuTeP shows roughly the same electrical conductivity and corrosion resistance as copper. Processing properties: hot forming: very good cold forming: good machinability: very good soft and hard soldering: good gas shielded welding: good burnishing: good Application: In electronics and electrical engineering, e.g. for small parts such as diode bases and transistors. For welding torch nozzles, screws, nuts, parts for screw connections and fitting components.

Chemical Composition

P [%] Te [%]
blur blur 1)2)
1) Source: blur
2) Remark: blur

Mechanical Properties

Semi-finished Product Strength Abbrevation Nominal Size [mm] Temperature [°C] Tensile Strength [MPa] Yield Strength (0.2% offset) [MPa] Elongation A10 [%] Elongation A100 [%] Elongation A [%]
blur blur blur blur blur blur blur blur blur 1)2)
blur blur blur blur blur blur blur blur blur 1)3)
blur blur blur blur blur blur blur blur blur 1)4)
blur blur blur blur blur blur blur blur blur 1)5)
blur blur blur blur blur blur blur blur blur 1)6)
blur blur blur blur blur blur blur blur blur 1)7)
blur blur blur blur blur blur blur blur blur 1)8)
blur blur blur blur blur blur blur blur blur 1)9)
1) Source: blur
2) Remark: blur
3) Remark: blur
4) Remark: blur
5) Remark: blur
6) Remark: blur
7) Remark: blur
8) Remark: blur
9) Remark: blur

Physical Properties

Temperature [°C] Density [g/cm³]
blur blur 1)
1) Source: blur

Cross Reference

Material Name Country Standard
CuTeP Bulgaria BDS 14894-79
CuTe(P) International ISO 1336-80
CuTeP Poland PN-79/H-87053
TebzE Hungary MSZ 705/1-69
C14500 USA UNS
C14500 USA ASME B16.22
C14500 USA ASTM B 124
DPTE USA ASTM B 224
C14500 USA ASTM B 283
C14500 USA ASTM B 301
DPTE USA ASTM B 5
DPTE USA SAE J 461
C14500 USA SAE J 463
CuTeP (2.1546) Germany DIN 17666

Producer/Supplier/Trade names

Tradename Supplier
Carotherm A Wieland Metal Services Germany GmbH, Düsseldorf
CuTeP KME Germany GmbH, Osnabrück
CuTeP CSN Carl Schreiber GmbH, Neunkirchen
OSNA-Cu58 Te KME Germany GmbH, Osnabrück

Material Compliance

REACh RoHS
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur blur blur blur
blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Density

Temperature [°C] Density [g/cm³]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Designation

Designation Material number Source
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur