Materials Portal Logo MATERIALS PORTAL

AlMgSiPb | 3.0615 Material Datasheet

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access

Material Description

Material Number Material Number (single) Standard Scope Standard Status Country Successor VDA 231-106 classification
3.0615 (DIN 1725-1 : 1983-02) 3.0615 DIN 1725-1 : 1983-02 DIN 1725-1 : 1983-02 replaced by DIN EN 573-3 : 2003-10 and DIN EN 573-4 : 2004-05 Replaced Germany EN AW-Al MgSiPb 2.1 1)
1) Remark: The material AlMgSiPb is a free-cutting alloy (boring and turning quality). It is warm and cold hardenable. Breaking the splinter is caused by the additive of Pb, and thus a troublefree splinter removal is possible with relatively high cutting performance. From the standardised free-cutting steel alloys this has to exhibit the smallest strength grade (F20 and/or F28), is however as only without surface protection corrosion resistant. It is suitable for a decorative surface treatment such as an anodising or a dyeing. The weldability is good. Heat treatment for hardening: solution annealing: 520 to 530 °C, quenching in water to 65 °C cold ageing: 5 to 8 at ambient temperature warm ageing: 4 to 16 h at 155 to 190 °C

Chemical Composition

Bi [%] Cr [%] Cu [%] Fe [%] Mg [%] Mn [%] Pb [%] Si [%] Ti [%] Zn [%]
blur blur blur blur blur blur blur blur blur blur 1)2)
1) Source: blur
2) Remark: blur

Mechanical Properties

Semi-finished Product Condition Designation of the delivered Condition DIN Delivery Condition EN Strength Abbrevation Nominal Size [mm] Temperature [°C] Tensile Strength [MPa] Yield Strength (0.2% offset) [MPa] Elongation A10 [%] Elongation A [%] Hardness HB | HBW
blur blur blur blur blur blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur blur blur blur blur blur 2)
blur blur blur blur blur blur blur blur blur blur blur blur 1)
blur blur blur blur blur blur blur blur blur blur blur blur 2)
1) Source: blur
2) Source: blur

Physical Properties

Temperature [°C] Melting Temperature [°C] Density [g/cm³] Mean Coefficient of Thermal Expansion (reference 20°C) [10^-6*K^-1] Thermal Conductivity [W/(m*K)] Electric Conductivity [MS/m]
blur blur blur blur blur blur 1)
blur blur blur blur blur blur 1)
blur blur blur blur blur blur 2)
1) Source: blur
2) Source: blur

Cross Reference

Material Name Country Standard
AlMgSiPb USA AA 6012
AlMgSiPbCd Austria ÖNORM M 3430
AlMgSiPb Switzerland SN 210900
AlMgSiPb Turkey TS 412
EN AW-Al MgSiPb (EN AW-6012) Germany DIN EN 573-3

Producer/Supplier/Trade names

Tradename Supplier
511 Diehl Metall Stiftung & Co. KG, Röthenbach
AB 13 OTTO FUCHS KG, Meinerzhagen
Al-Mg-Si-Pb Metall Dittrich, Velbert
AlMgSiPb Mittelrheinische Metallgießerei H. Beyer GmbH & Co KG, Andernach
AlMgSiPb Schreier Metall GmbH, Erkrath
AlMgSiPb Wieland Metal Services Germany GmbH, Düsseldorf
AlMgSiPb Manfred J.C. Niemann, Bremen
Autopan VDM Metals GmbH, Frankfurt/Main

Material Compliance

REACh RoHS
blur blur

Linear-elastic

Temperature [°C] Young's modulus [GPa] Bulk modulus [GPa] Shear modulus [GPa] Poisson's ratio
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Alternating stress

Temperature [°C] Stress ratio Mean stress [MPa] Alternating stress [MPa] Cycles
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur
blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Coefficient thermal expansion

Related Temperature [°C] Temperature [°C] Coefficient thermal expansion [10^-6*K^-1]
blur blur blur

Density

Temperature [°C] Density [g/cm³]
blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Thermal conductivity

Temperature [°C] Thermal conductivity [W/(m*K)]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Designation

Designation Material number Source
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur
blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur

Yield strength

Temperature [°C] 0.1% Proof strength [MPa] 0.2% Proof strength [MPa] Yield strength [MPa]
blur blur blur blur

Tensile strength

Temperature [°C] Tensile strength [MPa]
blur blur

Classification

WIAM Material Treatment Semi-finished product Dimension [mm] Load type Failure criteria Rolling direction Maximum stress [MPa] Strain at maximum stress [%] Source description
blur blur blur blur blur blur blur blur blur blur