10CrMo5-5 | 1.7338 Material Datasheet
Unlock Exclusive Materials Data
Gain access to a wealth of materials data by joining our Materials Portal.
Register for Free or Upgrade for Full AccessMaterial Description
| Material Number | Material Number (single) | Standard | Range of Application | Standard Status | Country | Predecessor | Successor | Application temperature [°C] | |
|---|---|---|---|---|---|---|---|---|---|
| 1.7338 (DIN EN 10216-2 : 2007-10) | 1.7338 | DIN EN 10216-2 : 2007-10 | DIN EN 10216-2 : 2007-10 replaced by DIN EN 10216-2 : 2014-03 | Replaced | Germany | 10CrMo5-5 | 10CrMo5-5 | 200 - 550 | 1) |
| 1) Remark: Seamless tubes of the high-temperature 10CrMo5-5 are used in steam boiler and pipeline construction, pressure vessel and apparatus engineering, especially in chemical industry and power station construction at temperatures from approx. 200 °C to maximum 550 °C and simultaneously high pressures. The total load and the special scaling circumstances can decrease or increase the temperature limit. When welding it should be considered that the behavior of the steel depends during and after welding on the applied heat treatment, the preparation and execution of the welding. |
Chemical Composition
| Al [%] | C [%] | Cr [%] | Cu [%] | Mn [%] | Mo [%] | Ni [%] | P [%] | S [%] | Si [%] | |
|---|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | ||||||||||
| 2) Remark: blur |
Mechanical Properties
| Semi-finished Product | Condition | Nominal Size [mm] | Temperature [°C] | Specimen Direction | Tensile Strength [MPa] | Yield Strength (0.2% offset) [MPa] | Elongation A [%] | |
|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| blur | blur | blur | blur | blur | blur | blur | blur | 1) |
| 1) Source: blur | ||||||||
| 2) Remark: blur |
Toughness Data (Impact)
| Temperature [°C] | Specimen Shape | Specimen Direction | Notch Impact Energy [J] | |
|---|---|---|---|---|
| blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | 1)2) |
| 1) Source: blur | ||||
| 2) Remark: blur |
Creep Rupture Behaviour
| Temperature [°C] | Creep Tensile Strength at 10^4 h [MPa] | Creep Tensile Strength at 10^5 h [MPa] | Creep Tensile Strength at 2*10^5 h [MPa] | Creep Tensile Strength at 2,5*10^5 h [MPa] | |
|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| blur | blur | blur | blur | blur | 1)2) |
| 1) Source: blur | |||||
| 2) Remark: blur |
Heat Treatment
| Heat Treatment | Temperature [°C] | Medium | |
|---|---|---|---|
| blur | blur | blur | 1)2) |
| blur | blur | blur | 1)2) |
| 1) Source: blur | |||
| 2) Remark: blur |
Cross Reference
| Material Name | Country | Standard |
|---|---|---|
| STBA23 | Japan | JIS G 3462 |
| STFA23 | Japan | JIS G 3467 |
| STHA23 | South Korea | KS D 3572 |
| P11 | USA | ASTM A 335 |
| K11597 | USA | UNS |
Producer/Supplier/Trade names
| Tradename | Supplier |
|---|---|
| 10CrMo5-5 | Vallourec Deutschland GmbH, Düsseldorf |
| 10CrMo5-5 | HEINE + BEISSWENGER Stiftung + Co.KG, Fellbach |
| 10CrMo5-5 | Rohrwerk Maxhütte GmbH, Sulzbach-Rosenberg |
Material Compliance
| REACh | RoHS |
|---|---|
| blur | blur |
Linear-elastic
| Temperature [°C] | Young's modulus [GPa] | Bulk modulus [GPa] | Shear modulus [GPa] | Poisson's ratio |
|---|---|---|---|---|
| blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur |
Alternating stress
| Temperature [°C] | Stress ratio | Mean stress [MPa] | Alternating stress [MPa] | Cycles |
|---|---|---|---|---|
| blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur |
| blur | blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
Designation
| Designation | Material number | Source |
|---|---|---|
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
| blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
| blur | blur | blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur | blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |
Yield strength
| Temperature [°C] | 0.1% Proof strength [MPa] | 0.2% Proof strength [MPa] | Yield strength [MPa] |
|---|---|---|---|
| blur | blur | blur | blur |
Tensile strength
| Temperature [°C] | Tensile strength [MPa] |
|---|---|
| blur | blur |
Classification
| WIAM Material | Treatment | Semi-finished product | Dimension [mm] | Load type | Failure criteria | Rolling direction | Maximum stress [MPa] | Strain at maximum stress [%] | Source description |
|---|---|---|---|---|---|---|---|---|---|
| blur | blur | blur | blur | blur | blur | blur | blur | blur | blur |