Compare Plastics, Metals, and More for Construction, Design, and Simulation - Materials Portal

Alutrans A Plus 5182-H111 Material Datasheet

Material Standard Values
Material Models for Simulation

Unlock Exclusive Materials Data

Gain access to a wealth of materials data by joining our Materials Portal.

Register for Free or Upgrade for Full Access

Material Description

Material Number	Standard	Scope	Standard Status	Country	Predecessor	Successor	Application temperature [°C]	VDA 231-106 classification
Alutrans A (VdTÜV WB 545 : 2007-06)	VdTÜV WB 545 : 2007-06	VdTÜV WB 545 : 2007-06 replaced by VdTÜV WB 545 : 2012-12	Replaced	Germany	Alutrans A	EN AW-Al Mg4,5Mn0,4	-196 - 80	2.1	1)
1) Remark: Valid for strip and sheet naturally hard AlMgMn-alloy Alutrans A Plus 5182-H111 - officially registered mark of the manufacturer Novelis weldable, formable Applcation range -196 °C to 80 °C: - for pressure tanks acc. to AD-Merkblatt 200 W 6/1 - for transport tanks acc. to GGVSE/ADR/RID - for pressure instruments acc. to guideline 97/23/EG, section 4 appendix I Smelting: - gas furnace (smelting process with following refining) Removing oxygen: - inline degasser Heat treatment: - softening

Chemical Composition

Cr [%]	Cu [%]	Fe [%]	Mg [%]	Mn [%]	Si [%]	Ti [%]	Zn [%]	Zr [%]
blur	blur	blur	blur	blur	blur	blur	blur	blur	1)2)
1) Source: blur
2) Remark: blur

Mechanical Properties

Semi-finished Product	Condition	Nominal Size [mm]	Temperature [°C]	Tensile Strength [MPa]	Yield Strength (0.2% offset) [MPa]	Elongation A [%]
blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	1)
blur	blur	blur	blur	blur	blur	blur	1)
1) Source: blur

Physical Properties

Condition	Temperature [°C]	Density [g/cm³]	Young's Modulus [GPa]
blur	blur	blur	blur	1)
1) Source: blur

Welding and Joining

Procedure	Welding and Joining - Evaluation	Information
blur	blur	blur	1)
blur	blur	blur	1)
1) Source: blur

Producer/Supplier/Trade names

Tradename	Supplier
Alutrans A Plus 5182-H111	Novelis Deutschland GmbH, Nachterstedt

Material Compliance

REACh	RoHS
blur	blur

Linear-elastic

Temperature [°C]	Young's modulus [GPa]	Bulk modulus [GPa]	Shear modulus [GPa]	Poisson's ratio
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur

Alternating stress

Temperature [°C]	Stress ratio	Mean stress [MPa]	Alternating stress [MPa]	Cycles
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur
blur	blur	blur	blur
blur	blur	blur	blur

Density

Temperature [°C]	Density [g/cm³]
blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Designation

Designation	Material number	Source
blur	blur	blur
blur	blur	blur

Linear-elastic

Temperature [°C]	Young's modulus [GPa]	Bulk modulus [GPa]	Shear modulus [GPa]	Poisson's ratio
blur	blur	blur	blur	blur
blur	blur	blur	blur	blur

Density

Temperature [°C]	Density [g/cm³]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur

Yield strength

Temperature [°C]	0.1% Proof strength [MPa]	0.2% Proof strength [MPa]	Yield strength [MPa]
blur	blur	blur	blur
blur	blur	blur	blur
blur	blur	blur	blur

Tensile strength

Temperature [°C]	Tensile strength [MPa]
blur	blur

Classification

WIAM Material	Treatment	Semi-finished product	Dimension [mm]	Load type	Failure criteria	Rolling direction	Maximum stress [MPa]	Strain at maximum stress [%]	Source description
blur	blur	blur	blur	blur	blur	blur	blur	blur	blur